Answers on compatibility, drive and maintenance of the Drillstarter pit bike starter. More help: contact or info@drillstarter.com.
General
Does the Drillstarter fit my engine?
The Drillstarter fits many pit bike engines. All models and engines offered by Ohvale fit – in addition to the engines already confirmed, e.g. Daytona 190. What matters is the flywheel thread: it must be M27x1 left-hand (LH). If so, only the ignition cover has to be modified. For most engines a centred 30 mm hole is enough; prepared ignition covers are available in the shop. The Drillstarter is not compatible with the Zongshen 190 with e-start (or e-start flywheel). See the compatibility overview.
What is the difference between the Classic MK2 and the Pro?
On the Classic MK2 Kit the safety freewheel sits in the freewheel unit on the flywheel. On the Pro Kit the freewheel coupling is integrated in the drive unit, and only a slim drive lug with a ball-head socket stays on the flywheel (angled use up to ±20°). The Pro drive lug does not fit the Classic MK2. The Drillstarter Pro barely protrudes from the ignition cover, perfect for MiniGP. The Drillstarter Classic MK2, on the other hand, is a perfect fit for the Zongshen ZS190, as its standard ignition cover is very deep. Details: Classic vs Pro.
Can I start several bikes with one drill?
Yes. The drive unit stays in the drill; a second freewheel unit (Classic MK2) or a second Pro drive lug (Pro) sits on the second engine. Both are available as single parts in the spare parts shop.
Do I need technical skills to install it?
Basic technical and manual skills are needed for installation. If you lack them, consult a specialist workshop. Installation and operation are at your own risk. Steps: installation and start.
Drive
Which cordless drill should I use?
Use a cordless drill (or a 220 V drill) with at least 2 gears. The 2nd gear should run at 1500 rpm or more, and battery voltage should be at least 18 V. The more voltage, the more torque; more than 70 Nm is recommended. A quick-stop function is important because it helps you find the right start position. Never start in 1st gear of the cordless drill (speed too low, high compression forces, risk of injury), and do not use an impact driver or the hammer-drill mode. Recommendation: Einhell TP-CD 18/80 Li-i BL with 80 Nm and a 2.5 Ah battery. More in the cordless drill guide.
Which crankshaft position is the right one to start the engine?
Plug the drive unit on and turn the whole drill anticlockwise. You will find areas with a lot of resistance and areas with hardly any, like going uphill and downhill. Within 2 revolutions (four-stroke cycle) there are two consecutive uphill climbs. The best position is shortly after the second uphill climb, because the drill can then build up some run-up as soon as you pull the trigger. The quick-stop function helps.
The chuck lock screw has sheared off. What do I do?
Depending on the drill and engine combination, the chuck lock screw can shear off under excessive load. Unscrew the remains from the shaft. A spare lock screw M6 × 27 mm with left-hand thread, suitable for most drills, is included. Before screwing the chuck back on, generously secure the thread with high-strength threadlocker, fit the screw and wait one day until it has fully cured. More screws are available in the shop: chuck lock screw.
I cannot get the sheared lock screw out. What can I do?
Note that the screw has a left-hand thread: to remove it you must turn it clockwise. If the break is very short, this can be difficult. Proven methods: (1) Cut a slot into the remaining piece with a rotary tool and turn it with a flat screwdriver and hammer. (2) Place an M6 nut on it, weld it to the remaining piece and unscrew it with an open-end wrench.
My drill cannot turn the engine over completely and stalls.
Possible causes: (1) The drill is too weak for the engine. Use a drill with at least 18 V; the 2nd-gear speed should exceed 1500 rpm. (2) Too much fuel in the combustion chamber raises compression. Unscrew the spark plug, turn the crankshaft over a few times with the Drillstarter, refit the plug and try again. Alternatively, push-start the engine once. On some engines compression also rises with the choke pulled. (3) The decompressor is not working properly – see the next question.
What can I do to reduce the engine's mechanical resistance?
Check that the decompression unit works properly and check the exhaust valve clearance. On larger engines from 190 cc the decompressor lever is spring-loaded. The spring tension can weaken over time. Fit a harder spring or pre-tension the spring by one extra turn. In the shop: harder decompression spring 190/212 cc.
Maintenance
How do I protect the parts from corrosion?
The main components of the Drillstarter are made of steel. Steel is not corrosion-resistant but is harder and more durable than many stainless steels. Keep all parts free of corrosion and coat the surfaces with a little bearing grease or similar. The most important spot is the thread that screws into the flywheel: before fitting, it must carry corrosion protection such as grease or copper paste. The thread is already supplied with copper paste.
Do I have to lubricate the freewheel bearing?
The freewheel bearing has lifetime lubrication from the factory. In dusty environments, however, dirt particles can settle in the bearing. In that case clean the bearing, rinse it for example with isopropanol and re-grease it with bearing grease.
How do I get the freewheel unit off the flywheel again?
Always keep the thread of the freewheel unit lubricated and protected against corrosion; this helps with removal.
Pro: The drive lug can be loosened with a 14 mm Allen key (hex key).
Classic MK2: The freewheel unit can be loosened with a long 16 mm socket.
MK1 (older version): Put the locking key on the housing of the freewheel unit and turn it clockwise to loosen it. If it is stuck, hit the end of the key with a rubber mallet. An oil filter wrench or flywheel holder can hold the flywheel. If it is still stuck: a pulsing impact works best. Loosen the locking screw (Torx) on the freewheel unit, pull the freewheel element off the round shaft, turn it by 180° and push it back on. This reverses the direction of rotation, and you can loosen the freewheel unit from the flywheel with an 18 mm socket and an impact wrench. Use short blows only; long blows can damage the freewheel unit.
More support: contact form or e-mail info@drillstarter.com. Manuals: user manuals (PDF).